The objective in applying a stain is usually to change the colour of the surface (typically bare wood) without hiding the texture of the material. Some stains, called semi-transparent stains, allow the grain pattern of the wood to be seen. With paint, we create a new appearance, which may be flat, satiny, or glossy, and the texture and grain of the surface is obscured. Stains are typically thinner than paints.

Yes, BST stain penetrates the surface of the material it is applied to. While a paint product adheres to the outer surface. BST stain sinks into the substrate and bonds below the surface.

The available historical evidence shows that Eichler used stains, not paint, on his homes, inside and out. One can speculate that, at least for the vertical-grooved siding, stains were employed so that the grooves stayed crisp and clean (the edges weren't softened by the paint), and some of the grain of the wood showed through (redwood siding was used throughout the 1950s). It is also possible that Eichler used stains because labor and materials costs were lower than for paint.

We do offer "certain styles of pre-primed balusters" but we do not do any painting or staining of any kind.

Jennings joinery prefers to paint or stain prior to glazing and assembly to properly seal the product. Also when using 6.38 Laminated glass (which is thicker than normal glass), if the inside rebate is not painted or stained prior to glazing then after the product is glazed the unsealed surface behind the glass edge is visible and un protected. Also after the bi-folds have been installed it is very difficult to coat the top and bottom of the doors to seal then correctly.

Ans: The insulating additive will help keep the deck cooler while providing a slightly slip resistant surface.

Quite frankly, we don't know and don't care. Both are effective. It really depends on what type of look you are trying to get from you shed. Plus, we are carpenters, not painters. Call a painter to get his opinion on which are better.

We recommend painting or staining after assembly. The rungs of the ladders sometimes are a tight fit and the finish may get marked up during assembly. Also, the wood glue used in the notched legs adheres better to unfinished wood. It is also much easier to paint or stain it when it is set up as opposed to all the individual pieces on the floor. If you paint it, we recommend you put a good primer coat, and two finish coats of a durable enamel paint.

One of the benefits of vinyl windows is never needing to strip, paint or stain them. Painting your vinyl windows can void your warranty.

No, staining is translucent and will appear marbled or old aged. Paint is generally more uniform and will peel.

There are unlimited choices for paint and stain colors. We do provide you a selection of colors, but if you have a specific color you'd like for your shutters, we can match it to a sample provided by the customer.

Yes. We stain and paint outdoor decks and patios. We also offer a power washing service for cleanup of decks, patios, and other exterior surfaces.

We recommend applying a protective finish to the fence once it is installed. This helps minimize the effects of weathering and maximize the life span of your fence.

Touch-up paint or stain is available for many of our styles. For ordering information, please contact the store where you purchased your furniture.

All of our paint and stain finishes are custom matched to the sample provided to us by the homeowner, for no extra charge.

Most clients prefer to stain the house. These are available in many shades and hues and are available widely. There are UV repellant brands which make it possible to prevent fading over time. However should you decide to use paint any oil based paint is satisfactory.

You should certainly protect your deck from unnecessary moisture intrusion and the harmful effects of the sun's ultra-violet rays. Use of a penetrating stain, containing water repellant ingredients in most cases will protect your deck best. The pigment in the stain will absorb the ultra-violet rays from the sun and protect the wood fibers from degradation. In most cases a stain will need maintenance every 2-4 years while clear sealers require maintenance every 1-2 years.

All products make from timber must be stained or painted to ensure the good looks of the cubby and to reduce splitting and to seal the timber against weathering. We highly recommend staining or painting while the cubby is still in panel form and not assembled. It is easier to paint the pieces when flat on the ground.

It is very difficult to answer this question as it depends on the weather conditions and if the cubby is in full or partial sun, but generally when the original painting or staining has begun to deteriorate or look dry. We Recommend Quality Cubby Cedar Coating Stain which is available from our store. Read the instructions before you start and use the level to make sure the floor is level before you start to install the walls.

Please remove lids from empty cans, let the can and lid dry and discard in the garbage. Garbage haulers will take them only if the lid is removed. Take partially full or full cans of paint to Metro Central’s Hazardous Waste Depot, or weekend roundup events for recycling.

Even though the lumber may be kiln-dried before treatment, using water-borne preservatives restores moisture to the wood. Too much moisture in the wood may prevent the stain or paint from penetrating the wood sufficiently. It is best to test the wood by painting or staining a scrap piece to see if it applies properly. If not, wait until it does. A water repellent should be applied annually. Do not use latex paints. Semi-transparent, oil-based stains work best.

Northgate Garage Doors, Inc., does not specifically recommend one particular kind of paint, stain, or varnish over another. But, it seems Watco™ oil and Behr™ spar varnish have become popular brands that many people use with excellent results. Watco and Behr™ products can be found at most home improvements stores.

Answer: It should not be used inside, the residue is to difficult to remove without rinsing, we recommend only using it outside

While Renewal by Andersen® windows come pre-finished, they can be painted or stained when necessary. There are over 20 standard color combinations. Pine, Oak, and Maple interiors are available for custom staining. Exteriors can be painted to match unusual color schemes. Custom color Fibrex® is available on larger commercial projects.

These products are hazardous wastes and are accepted at the Moderate Risk Waste (MRW) Facility for proper disposal

Spot removal is soiling that can most likely be removed with regular cleaning methods. A stain (usually deemed permanent) requires other means of removal and may not always be possible. For spot removal tips click here.

Transparent stains have considerably less pigment than opaque stains, in order to allow the grain of the wood to show through. Opaque stains obliterate or hide the grain; and because of the added protection of the wood from UV radiation, will last longer before needing to be re-applied.

Is it necessary to mix separate buckets if a job requires multiple containers? (for bagged product this is recommended for color variance)