The available historical evidence shows that Eichler used stains, not paint, on his homes, inside and out. One can speculate that, at least for the vertical-grooved siding, stains were employed so that the grooves stayed crisp and clean (the edges weren't softened by the paint), and some of the grain of the wood showed through (redwood siding was used throughout the 1950s). It is also possible that Eichler used stains because labor and materials costs were lower than for paint.

No! Vinyl siding is virtually maintenance free. The most you ever have to do is give your home a wash down with soap and water once or twice a year.

Since plywood is made up of many layers of wood that expand and contract, coatings applied to it are prone to cracking and checking. Stain is an ideal coating for rough sawn siding since it is designed to provide a natural, rustic appearance. Use either an alkyd semi-transparent or an alkyd or latex solid color stain. If a less-natural finish is desired, an acrylic latex primer followed by an acrylic latex topcoat can also be used.

That will probably seal them in. It may solve your problem, but will give a pebbly appearance to your paint job. Each repainting will seal in the artillery fungus even more. There are no fungicides legally registered (by EPA) against the artillery fungus. Bleach, if it worked, would be very temporary, as it leaches out with each rain. We tested 14 different fungicides in the laboratory, but have to take the experiment to the field.

We do offer "certain styles of pre-primed balusters" but we do not do any painting or staining of any kind.

Jennings joinery prefers to paint or stain prior to glazing and assembly to properly seal the product. Also when using 6.38 Laminated glass (which is thicker than normal glass), if the inside rebate is not painted or stained prior to glazing then after the product is glazed the unsealed surface behind the glass edge is visible and un protected. Also after the bi-folds have been installed it is very difficult to coat the top and bottom of the doors to seal then correctly.

This helps the performance of the stain on the side you do see. It controls the absorption of water on the backside, which not only helps the front side stain to look nice longer, but it also helps to avoid dimensional problems such as cupping and warping.

No. Our siding is virtually maintenance free. The most you ever have to do is give your home a washing with soap and water once or twice a year. We offer the widest variety of trim pieces in the industry. Everything from function utility trims to substantial wide trims resembling dimensional lumber, fluted cornerposts and decorative crown molding for window headers.

Note: Boards close to the ground and boards installed on chimneys are the first to become damaged. Look there first.

Ans: The insulating additive will help keep the deck cooler while providing a slightly slip resistant surface.

Quite frankly, we don't know and don't care. Both are effective. It really depends on what type of look you are trying to get from you shed. Plus, we are carpenters, not painters. Call a painter to get his opinion on which are better.

We recommend painting or staining after assembly. The rungs of the ladders sometimes are a tight fit and the finish may get marked up during assembly. Also, the wood glue used in the notched legs adheres better to unfinished wood. It is also much easier to paint or stain it when it is set up as opposed to all the individual pieces on the floor. If you paint it, we recommend you put a good primer coat, and two finish coats of a durable enamel paint.

One of the benefits of vinyl windows is never needing to strip, paint or stain them. Painting your vinyl windows can void your warranty.

No, staining is translucent and will appear marbled or old aged. Paint is generally more uniform and will peel.

The objective in applying a stain is usually to change the colour of the surface (typically bare wood) without hiding the texture of the material. Some stains, called semi-transparent stains, allow the grain pattern of the wood to be seen. With paint, we create a new appearance, which may be flat, satiny, or glossy, and the texture and grain of the surface is obscured. Stains are typically thinner than paints.

There are unlimited choices for paint and stain colors. We do provide you a selection of colors, but if you have a specific color you'd like for your shutters, we can match it to a sample provided by the customer.

Yes. We stain and paint outdoor decks and patios. We also offer a power washing service for cleanup of decks, patios, and other exterior surfaces.

We recommend applying a protective finish to the fence once it is installed. This helps minimize the effects of weathering and maximize the life span of your fence.

Touch-up paint or stain is available for many of our styles. For ordering information, please contact the store where you purchased your furniture.

All of our paint and stain finishes are custom matched to the sample provided to us by the homeowner, for no extra charge.

Most clients prefer to stain the house. These are available in many shades and hues and are available widely. There are UV repellant brands which make it possible to prevent fading over time. However should you decide to use paint any oil based paint is satisfactory.

Yes, BST stain penetrates the surface of the material it is applied to. While a paint product adheres to the outer surface. BST stain sinks into the substrate and bonds below the surface.

You should certainly protect your deck from unnecessary moisture intrusion and the harmful effects of the sun's ultra-violet rays. Use of a penetrating stain, containing water repellant ingredients in most cases will protect your deck best. The pigment in the stain will absorb the ultra-violet rays from the sun and protect the wood fibers from degradation. In most cases a stain will need maintenance every 2-4 years while clear sealers require maintenance every 1-2 years.

All products make from timber must be stained or painted to ensure the good looks of the cubby and to reduce splitting and to seal the timber against weathering. We highly recommend staining or painting while the cubby is still in panel form and not assembled. It is easier to paint the pieces when flat on the ground.

It is very difficult to answer this question as it depends on the weather conditions and if the cubby is in full or partial sun, but generally when the original painting or staining has begun to deteriorate or look dry. We Recommend Quality Cubby Cedar Coating Stain which is available from our store. Read the instructions before you start and use the level to make sure the floor is level before you start to install the walls.

Although we use the best products possible for our siding, the life of your new siding depends greatly on the paint job it gets. You must use a good quality primer/sealer and a high quality top coat that is compatible with the primer to get the best results. Make sure the edges are primed/sealed BEFORE installation. Once your siding is installed it is impossible to seal the edges properly. The prime coat is the most important coat. Oil/alkyd primers are recommended; latex primers also work well.

Yes. All surfaces must be clean and free of debris prior to painting. Repainting aluminum siding can make it appear new and can be done for approximately 1/4 to 1/3 the cost of having new siding installed.

Yes, as long as the surfaces are clean. Run your hand over the vinyl siding, on the sunny (usually south) side of the house. If there is white chalky residue, the house must be scrubbed or powerwashed, or else the paint will not adhere well. You can also paint factory-painted gutters, downspouts and doors. If the surface is very glossy, either use a bonding primer, or sand the surface to ensure good adhesion.